Aver NXU8000 User Manual

Hybrid Capture Card NV6120T/NV6240T/NV6480T/NV8416T NXU8000 series User’s Manual Nov. 2012

ix Network Setting ... 206 Schedule Setting ...

88 (11) Dual Monitor Enable/disable dual monitor display. Click Setting to select display order of Preview (main system), Playback, and EMap. (12) P

89 (14) System Configuration The System Configuration is in different display on Window XP and Windows 7. Following are described System Configuratio

90 To format and partition hard disk: 1. Click + button to add the selected hard disk into Partition Table section. 2. User can adjust the capacity

91 fill in the IP address and file folder of file server or NAS on your network in Folder. 2. And then, click Finish to make the connection. 3. Af

92 Others Printer Setting Click Add Printer and following the wizard to install a printer.

93 Regional/Language Setting When DVR application is using different language of UI besides English, user can select the corresponding region and lan

94 Device Management To manage the DVR system devices. Network Connection To manage the connection of the network. Phone and Modem options To setup

95 Date/Time Setting 1. Select the Time Zone of DVR server located 2. Select the Month and Date. Click arrow button can switch to different month.

96  Windows 7 In System Configuration section, user can setup keyboard language, printer, PPPoE setting, Audio, Phone and Modem, Map/Disconnect net

97 Memory Displays DVR system’s memory usage. Network Displays DVR system’s network usage. Click drop-down list to select LAN2 and view LAN2 usage

x APPENDIX B CONFIGURE UPNP ... 261 APPENDIX C NETWORK SERVICE POR

98 CameraInfo Displays DVR system’s cameras information – Camera name, ftp in Live and Recording, and current status. In Status, a is analog camera c

99 S.M.A.R.T Displays DVR system’s hard disk information. User can view information of each hard disk or hard disk portion on DVR system. Double-c

100  Keyboards/Input methods Select the keyboard or input language.  PPPoE Setting To configure the LAN setting of DVR system. 1. Click PPPoE

101 3. After DVR system reboot, Click Setup >> System >> System Configuration >> PPPoE >> Add button >> Broadband(PPPo

102 4. Enter the PPPoE’s User name and Password. Mark Remember this password and keep Connection name as default -- Broadband Conn

103 6. User will see the name of PPPoE connection that user has setup list in Dial-up and Virtual Private Network settings. 7. Then, click OK and r

104  Sounds Setting Adjust audio volume of system.  Printer Click Add Printer and following the wizard to install a printer.

105  Device Management To manage the DVR system devices.  Phone and Modem options To setup the modem dial-up settings.

106  Map Network Drive To add network storage, the Internet storage drive/folder must be mapped as Network Driver in DVR server. Follow the below s

107 (15) System Controller Setup To configure the parameters that is for communicating with the System Controller (an optional accessory). For operat

xi Manual Conventions The following conventions are used throughout this manual. Caution symbol is intended to alert the user of the important insta

108 5.1.1 To Set the POS Setting General Setting 1. In the System Setting dialog box, POS section, click Setting. 2. In the POS Console Setting di

109 (2) Protocol: To select the protocol, click Setting button (see Setup POS Protocol) (3) Skip first: Set the number of lines you want to be remove

110 Setup POS Device There are 4 default POS devices. If user uses the POS device beside defaults, user can add new POS device and rules. The POS dev

111  Add Rules 1. Select the POS device form device list 2. Click Add in Rules section 3. In Rule Setting window, select Group. Each group has a

112  Adjust Rule Priority User can set the priority of rule groups. Select the group and click up/down arrow button to move the priority level. The

113 Setup XML POS Device XML can only work with the POS data is transmitting in XML format.  Device: select or add a new device. Only device that

114 Please refer to the following example for more detail. <TicketStart> → Page Start <Header> → Root tag <MessageVersion>

115 Advanced Setting To setup POS text display position, text font and color. 1. In the System Setting dialog box, POS section, click Setting >&g

116 5.2 Camera Setting NV capture card series and NXU8000 series are different in Camera Setting. The following sections are described each in detai

117 - Name Change the camera name - Description Add a short comment (4) Video Adjustment (Analog Camera Only) Adjust the Brightness, Contrast, Hue

1 Chapter 1 Introduction 1.1 NV series AVer DVR is a 32-bit PCI video capture card that works as a digital video surveillance system

118 - IP Camera The video source is coming from Network camera or IP camera. Click Setup to enter the IP Camera Settings window.  IP camera moti

119 In Search Result window, the camera is in red text that is configurable. User can double-click on the camera is in red text and configure the IP

120  Using RTSP protocol: If the IP camera supports RTSP protocol, user can use RTSP protocol to connect with IP camera. - Protocol: Select the “R

121  Using URL: In the IP Camera Settings dialog box, select to connect using URL and then enter the URL of the IP camera(If you are not sure of th

122  Detail setting of IP camera: In Camera Setting interface, click Detail to configure more parameters of the IP camera. Click OK to save the con

123 date and time block to set the connection schedule.  I/O Control: To setup the sensor and relay devices that is installed on IP camera.  Sen

124  Relay Setting: To setup relay device that is embedded on the camera. 1. Click the drop-down list and select the relay ID number. 2. Enter re

125 5.2.2 NXU8000 series In the Camera Setting dialog box, click OK to accept the new settings, click Cancel to exit without saving, and click Defau

126 (6) Input  Add IPCam: To connect an IP camera or Remote DVR. Click Add IPCam button and select the type of camera and click OK to continue.

127 In Search Result window, the camera is in red text that is configurable. User can double-click on the camera is in red text and configure the IP

2 NV6480T Package NV6480T package includes the following: (1) (2) (3) (4) (5) (6) 8FC - 26P (7) (1) NV6480T (3) 2 x AV cable (5) Instal

128 - Add Remote DVR: After select camera type as Remote DVR, click Add IPCam button to make a connection to remote DVR/NVR server. In Re

129 - Transcode by MPEG4 Encoder: NVR system is decoding the video and compress video again by using MPEG4 encoder.  Preview Setting: preview

130  Relay Setting: To setup relay device that is embedded on the camera. 1. Click the drop-down list and select the relay ID number. 2. En

131 5.2.3 Setup the Object Counting i The DVR system only supports 4 channels for object counting function. 1. Click Detail to enter the object cou

132 9. Click OK to save the setting. Click Cancel to leave the setup window without saving. 10. The object counting information will be display on

133 5.2.4 To Setup the FaceFinder To setup the human face detection and capturing from live and recorded video for security issue. Click Detail to e

134 Control Setting of External Device: Set the conditions of the face detection that is trigger by outside device such as sensor, relay device. -

135 5.2.5 Setup PTZ Tracking PTZ tracking allows user to setup a select range for PTZ camera to tracking the object automatically when object is out

136 4. Click OK to complete the setting. 5. When the PTZ tracking has been setup, user should see the PTZ tracking icon ( ) on the preview screen.

137 5.2.6 Create a Camera Group Follow the below steps to create a camera group. The maximum of group number is 64. The default group can be deleted

3 1.2 NXU8000 series AVerTM NXU 8000 series is a software license that offers a way to install NVR surveillance application in your computer or upgr

138 3. Drag the camera from Camera list section to the group. 4. Right-click the camera can rename, delete, display/no display video of camera, an

139 9. User can easy to view and manage the camera group in preview/advanced mode by click camera tree icon (see also Chapter 4.3(11) Camera Group T

140 5.2.7 IP camera PnP Setup To connect AVer IP camera series without any configuration; just easy as plug and play. i - The IP camera PnP setup n

141 5.3 Recording Setting In the Recording dialog box, click OK to accept the new settings, click Cancel to exit without saving, and click Default t

142 (2) Recording Mode  Weekly Record Mode: Setup the recording schedule by week. The horizontal blocks from 00 to 23 represent the time in 24-hour

143 The recording modes are listed below: - Always Recording Record the video from the selected camera and save it to the designated storage p

144 (6) Quality(Analog camera only) Adjust the video quality. The higher the value, the lower the compression level and uses more hard disk space.

145 definition. (11) Individual Adjustment(Analog camera only) To adjust recording frame rate of each channel. Max available frames are total frames

146 The symbol would appear on the upper right corner of the encrypted video screen. You may see the video during live recording. To decrypt the

147 NV8416T   (14) Group Click to view the camera group that user has been setup in Camera setup (see also Chapter 5.2.4). (15) Camera Click to

4 1.3 Card Parts NV6120T Card Parts DVI AV In portI/O connectorReset pinWatchdog pin NV6000T series Card Parts (6420T/6480T) i NV6240T card only has

148 5.3.1 To Mask/Shield an area on the screen 1. In the Mask/Shield Edit section, activate the Enable Mask/Enable Shield check box. 2. In the Edi

149 5.4 Network Setting In the Network Setting dialog box, click OK to accept the new settings, click Cancel to exit without saving, and click Defau

150 (6) Network Video Configuration Set up the video quality and frame rate for viewing and transmitting to the remote program. Scrolling adjust bar

151 - Enable HandyViewer Enable remote users to use a PDA or a mobile phone to access DVR server and select the video size and quality. (See also Ch

152 5.5 Schedule Setting Schedule to record, backup, enable network, reboot and disable alarm of all the cameras either weekly or one time. The numb

153 - Enable Network Activate DVR remote system to access at the set time. After the appointed time, the Network function will be disabled. If the

154 5.6 Backup Setting In the Backup Setting dialog box, the number from 00 to 23 represent the time in 24-hour clock. The numbers from 01 to 16 rep

155 window will display on screen automatically when the DVR system detects CD/DVD-ROM disk or USB storage device. Right after user select the period

156 5.7 Sensor Setting The I/O device must be installed to use this function. The DVR system also support external I/O box and user can install exte

157 5.8 Relay Setting The I/O device must be installed to use this function. To set the Relay Setting: 1. Click the drop-down list and select

5 Chapter 2 Hardware Installation 2.1 Minimum System Requirements Verify if the computer meets the minimum system requirements. Product Item Re

158 5.8.1 To Setup External I/O Box i NVR server needs to purchase the E-I/O box in order to have the sensor and relay connection. The DVR system c

159 9. In External I/O box setup dialog, user will see all added External I/O. Click added External I/O box and click Add to scan the connected rela

160 13. To view the all I/O devices information, click I/O Map.

161 5.9 Alarm Setting In the Alarm Setting dialog box, click Add to insert and set new alarm setting, click Delete to remove the selected alarm sett

162 “Trigger if all” to activate if it falls to all conditions. - Motion Detected: select and click on the camera number (01 to 16) to set the condi

163 - Enable/disable the Abnormal Event check box, to set the condition of the event for system to alarm.  System Reboot: when the DVR system reb

164  Trigger if once: Send out the alarm when the selected camera match the illegal entry has selected.  Trigger if the amount exceeds: Send out

165 - Alarm Reset Time: Set a time for the alarm auto reset. When an alarm happen such as motion detected and video loss, the alarm will reset at th

166 b. Select the display mode – 1 Channel or Full Screen. c. Retrieve time: set the waiting duration before system switching back to original Prev

167 - PTZ preset point Position the PTZ camera based on the preset point setting. To setup click Detail (see also Chapter 5.9.8). - Alarm SOP (Stan

6 Product Item Recommended NV6000T (6240T/6480T) CPU 3. Pentium® 4 3.2 GHz or higher 4. Dual core CPU is highly recommended Mother Board Intel G4

168 5.9.1 To Setup Alarm Relay 1. Next to the Relay Output check box, click Detail. 2. In the Alarm Relay dialog box, select from the available re

169 5.9.3 To Setup Call Out List 1. Next to the Make Phone Calls check box, click Detail. 2. In the Call Out List, click Add to insert a new conta

170 5.9.4 To Setup Send E-mail Setting Next to the Send Email check box, click Detail. In the E-mail Setting dialog box, click OK to exit and save t

171 5.9.5 To Setup FTP Setting 1. Next to the File Transmission via FTP check box, click Detail. 2. In the FTP Setting dialog box, enter the FTP S

172 5.9.6 To Setup Alarm Recording Setting 1. Next to the Start Recording check box, click Detail. 2. In the Alarm Recording Setting dialog box, s

173 5.9.7 To Setup SMS/MMS Setting To use this feature, GSM/GPRS modem is required. Connect the GSM/GPRS modem to the serial COMM port of PC. Beside

174 5.9.8 To Setup PTZ Preset Point Beside the PTZ preset point check box, click Detail. In the Trigger PTZ Preset Setting dialog box, select the PT

175 5.9.10 To Setup CMS Setting Beside the Send to CMS check box, click Detail. Click OK to accept the new settings and Cancel to exit without savin

176 5.9.11 To Setup POS Keyword Setting 1. Beside the Send to POS Keyword check box, click Detail. 2. In the POS Keyword Setting, select the cam

177 5.9.12 Missing, Suspicious Object, and Scene Change Detected  Missing Object Select the certain object on the screen for the system to detect;

7 Product Item Recommended NV6000T x 2 (32 Channel) CPU Intel Core 2 Duo E6600 2.4 GHz Mother Board Intel G41/P43/X58/H55/P55/H61/H67/P67/Z68 chipse

178 8. To reset all object frames, click Clean. To clean an object frame, click right button of mouse and drag the object frame that user want to cl

179 5.10 User Setting Users with Administrator privileges can access User Setting. The maximum user accounts are 256. In the User Setting dialog box

180 - Remote Record Allow the user to record video at remote site. - IP Camera Enable/disable user to add new IP camera when using the PCViewer. -

181 Chapter 6 Playback Backup Video You can playback the backup files using QPlayer applications. When you back up the recorded file, QPlayer applic

182 Name Function (5) Playback Control Buttons Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame. Slow

183 Name Function (12) Full screen View in Playback-compact mode. To return, press the right button of the mouse or ESC on the keyboard or click the

184 Chapter 7 Functional Keys and Debug Tool 7.1 Using Functional Keys The DVR system provides shortcut keys. The table shows the function keys and

185 7.2 Using Debug Tool Debug Tool helps user to save a system log report or record all operate processing in order to debug when DVR system has

186 Chapter 8 Using the Remote Programs You can use Microsoft Internet Explorer to access DVR server by entering the IP address or domain name. To u

187 8.1 Familiarizing the PCViewer 8.1.1 PCViewer Screen Right-clicking on the PCViewer video screen, enables user to start video record

i Manual Updates Following are listed the new functions for the version 7.9.0.0033 and above of NV/NXU surveillance software. [Note] User can press F1

8 Product Item Recommended NV8416T CPU 1. Pentium® 4 3.2 GHz or higher 2. Dual core CPU is highly recommended Mother Board Intel G41/P43/X58/H55/P5

188 Name Function (1) DirectDraw Enhance the video quality. i Not all graphic cards can support this function. If you cannot see the

189 8.1.2 PCViewer Control Panel Name Function (1) Preview Mode Switch to preview mode control panel. (2) Playback Mode Switch to playback mode c

190 Name Function (6) Audio Enable/disable remote sound. (7) Remote setup Change the DVR server settings (see also Chapter 8.1.3). (8) Remote Emap

191 8.1.3 Playback Mode Control Panel i The PCViewX.cab. installation is required for first time using PCViewr playback function. The PCViewX.cab in

192 Name Function (7) Play button After select the file, click it to start playback. Move to the begin Move to the end Time progress ba

193 8.1.4 To Setup Remote System Setting There are two type of remote setup mode – Basic Setting and Advance Setting. Select the setup mode and clic

194 still record the video and preview it in playback mode. - Name Change the camera name. - Description Add a short comment. (4) Video Adjustmen

195 Advance Setting In Advance setting, user can configure remote DVR in more detail. System Setting In the System Setting window, click Update to a

196 click OK. (5) AutoScan Period Set the display time gap from 3 to 10 sec. before it switches to the next camera. (6) Login Enable the conditions

197 (8) Dual Monitor To enable/disable dual monitor function. (9) POS Set from which camera screen to display the data from the POS equipment. Click

9 2.2 NV6120T/NV6240T/NV6480T/NV8416T Hardware Combinations AVer NV DVR provides powerful surveillance functions and flexible hardware combinations

198 Preview mode) will be saved as next time call out position when close 6. Select the Cameras of iPOS live data that want to be display on Prev

199  IPCam Module: displays current IP camera patch version. Click Update button to upgrade the IP camera patch.

200 Camera Setting Select the camera from remote DVR servers to modify settings. In the Camera Setting window, click Update to save and apply the new

201 (6) Auto Brightness Control Automatically adjust the brightness. (7) Night View Automatically adjust the exposure to make the image more visi

202 Record Setting In the Recording setup window, click OK to accept the new settings, click Exit to exit without saving, and click Default to revert

203 DVR system will record when the voice exceeds the intensity value in Voice Detection setting. - No Recording The system won’t do any recording.

204  Video Encryption Enable/disable to encrypt the recorded video that way only the person who knows the password can clearly view the video playb

205  Enable Storage Optimization Enable/disable to save more storage space. Click Detail button to select the type of storage optimization.  Mono

206 Network Setting In the Network Setting dialog box, click Update to accept the new settings, click Exit to exit without saving, and click Default

207 that is when the WebCam 2-Way Talk button is activated. (See also Chapter 8.1 #6). The default port of voice phone is 9999. (8) Network Time Sync

10 Hardware Combinations Camera Input Audio Input Sensor Input Relay Output NV6120T Card (4Channels) NV6480T card (8Channels) I/O Card 1 1 0 20 20

208 - Enable HandyViewer Enable remote users to use a PDA or a mobile phone to access DVR server and select the video size and quality. (See also Ch

209 - Network Bandwidth Limit  By Channel: Set the network bandwidth by each channel.  All: Set the total network bandwidth consumption limit.

210 Schedule Setting Schedule to record, backup, enable network, reboot and disable alarm of all the cameras either weekly or one time. The number fr

211 - Backup Save another copy of all the data at the set time and specified backup path. DVR automatically updates and only backup the data that ar

212 Alarm Setting In the Alarm Setting dialog box, click Add to insert and set new alarm setting, click Delete to remove the selected alarm setting,

213  System Reboot: when the DVR system reboot without abnormal condition, the system will send out the alarm message.  Abnormal Reboot: when the

214 - TV Out i Alarm TV Out function doesn’t support for NVR server. Switch to only display the video on TV from where the alarm is activated. - E

215 To Setup FTP Setting 1. Next to the File Transmission via FTP check box, click Detail. 2. In the FTP Setting dialog box, enter the FTP Server

216 To Setup Alarm Recording Setting 1. Next to the Start Recording check box, click Detail. 2. In the Alarm Recording Setting dialog box, select t

217 8.2 Familiarizing the Remote Console Buttons Remote Console application can be installed from Software CD, too. Name Function (1) Exit Close th

11 2.3 NV6120T Hardware Installation The NV6120T can support up to 8 cameras and 8 audio inputs. 2.3.1 Installing NV6120T and I/O card 1. Remove

218 Name Function (12)Snapshot Capture and save the screen shot either in *.jpg or *.bmp format. (13) Event log Show the record of activities that ta

219 8.2.1 To Setup Remote Console Setting Click OK to exit and save the setting and Cancel to exit without saving the setting. (1)(2)(3)(4)(5) (1) S

220 column if you know. Or click Browse to find the folder direction. Click Finish to complete the network drive mapping. After the network drive has

221 8.3 Familiarizing the Buttons in PTZ Camera Controller Name Function (1) Close Exit PTZ camera controller. (2) Setup Select the PTZ camera. (

222 8.4 Using the Remote Playback To use this feature, first you need to select the source of the file. In the Select Playback Mode dialog box, ch

223 To Make a Selection: 1. Select the date in the calendar. Use and buttons to shift the calendar to the left or right. 2. In the table be

224 8.4.1 Familiarizing the Local Playback Buttons Name Function (1) Split Screen Mode Select from 6 different split screen types to playback the r

225 Name Function (5) Playback Control Buttons Begin: Move at the beginning of the recorded video file. Previous: Go back to the previous frame. Slow

226 Name Function (11) Export Export includes Snapshot, Print, and Output Video Clip function. Snapshot: Capture and save the screen shot either in

227 Name Function (20) De-interlace To enhance the video quality. Set the de-interlace mode to #1, if you are capturing motionless picture

12 2.3.2 Installing (2) NV6120T and (2) I/O card i The PC motherboard needs to have 2 PCI-Ex1 slots for installing 2 NV6120T cards. 1. Remove the P

228 8.4.2 Familiarizing the RealTime Playback Buttons Name Function (1) Exit Close the application. (2) Split Screen Mode Select from 6 different s

229 Name Function (5) Playback Control Buttons Next: Go to the next frame. End: Go to the end of the recorded video file. (6) Archive – Select the d

230 Name Function (13) Event log Show the record of activities that take place in the system. To filter the records, select and click the option butt

231 8.4.3 Familiarizing the Download and Playback Buttons (15)(2)(1)(3)(4)(7)(8)(11)(12)(13)(14)(5)(9)(6)(10) Name Function (1) Exit To exit applica

232 Name Function (7) Export Export includes Snapshot, Print, and Output Video Clip function. Snapshot: Capture and save the screen shot either in

233 Chapter 9 Web Tools The bundled Web Tools includes Dispatch Server and Remote Backup program. To install Web Tools, place the CD into the CD-ROM

234 9.1.1 To Add DVR server User need to add a DVR server and make connection in order to setup remote DVR server. 1. Click Add 2. In Edit DVR wi

235 9.1.2 To Setup Remote DVR Server Select the DVR server from listing and click Setup to configure remote DVR server. Please refer to Advance Sett

236 9.2 Remote Backup Remote Backup is purely for backing up the *.dvr file from the DVR sever. You can select between Auto Backup and Manual Backup

237 4. In the Add New DVR window, enter the Name, IP, user ID, and password. 5. Select the Backup mode: Auto Backup mode: the backup will automati

13 2.4 NV6000T(6240T/6480T)Hardware Installation The NV6000T can support up to 16 cameras and 8 audio inputs 2.4.1 Installing (2) NV6000T card i Th

238 7. Click Start to begin backup and click Stop to stop backup progress. 8. For manually backup, click file select button and select the DVR

239 11. If user wants to burn the back file into DVD disk, click Burn button and select the file to burn.

240 9.3 iMatrix Application The AVerTM iMatrix is a monitoring system that enables user to monitor remote DVR servers and CMS server through an in

241 9.3.1 Software Installation This chapter describes how to install the iMatrix software. - Before installing the software, make sure the Window

242 Installing the iMatrix Software in Windows XP/7 1. Place the installation CD into the CD-ROM drive then click Install Web Tool. 2. All appl

243 4. Enter the administrator ID and password and click Next. 5. Select the install destination path if user wants install in different path besi

244 9.3.2 Using the iMatrix Running the iMatrix Software To run the application, double-click on your PC desktop or click Start > Programs >

245 Name Function (1) Exit Call up the Logout dialog box. In the logout dialog box, you may do the following: - Click Exit to close the iMatrix

246 Using Monitor Controller User can use Monitor Controller to switch different monitor set for monitoring and add/delete the channel in monitor set

247 8. To delete channels from monitor set, right-click on channel and select Recover. 9. Click arrow button to close the sub window. i Right-clic

14 2.4.3 Installing (2) NV6000T and (2) I/O card (Optional) 1. Remove the PC case cover. 2. Remove 2 brackets that cover the PCI slot and 2 bracke

248 Familiarizing the Buttons in PTZ Camera Controller Name Function (1) Close Exit PTZ camera controller. (2) Setup Select PTZ cameras. (3) AutoPan

249 9.3.3 Customizing the iMatrix System In the iMatrix application, click the button to customize the iMatrix system. In the Autho

250 default the set language is in English. (3) Screen Setting Enable/disable monitor for monitoring. Only the monitors that connect with iMatrix sy

251 DVR Setup Add the DVR servers for monitoring. i iMatrix only supports 16 DVR servers To Add and Remove DVR Server 1. Click Setup. 2. In the A

252 Camera Setup Select the camera from different DVR servers in order to monitor in one group. The selected cameras will be played on Monitor screen

253 camera from the Monitor Layout window, select the camera and right-click to select Recover. To delete all cameras, click Clear All button. User c

254 i - Click right mouse button and drag on screen can enlarge viewing. Click right mouse button again to back to normal view. - Press F1 will di

255 User Setting iMatrix supports 256 user account that includes operator and administrator account. 1. Click Setup. 2. In the Authorization dialog

256 9.3.4 Using the Playback Function User can playback recorded video from the remote side of the DVR server. i - Playback function must be enab

257 Button Function Select recorded vide to playback from remote DVR server hard disk. Select the date on the calendar and the time from 00 to 23 to

15 2.5.2 Install (2) NV8416T cards 1. Remove the PC case cover. 2. Remove 2 brackets that cover the PCI-Ex4 slot. Save the screws 3. Press the NV

258 Chapter 10 Using the Remote Control Server The bundled Remote Control Server enables the PC with Central Management System program (CM3000) inst

259 Appendix A Registering Domain Names DDNS (Dynamic Domain Name Service) is a data query service mainly used on the Internet for translating dom

260 II. Register the Domain Name on http://dyn.com/dns/ 1. Open the browser on your PC and enter the URL http://dyn.com/dns/ 2. Follow the DyD

261 Appendix B Configure UPnP DVR application support UPnP function that can automatically configure the port setting of DVR into the local router

262 3. Click Settings button and select Exception tab. The Windows Firewall appears. 4. Mark the UPnP Framework check box and click OK.

263 Appendix C Network Service Port The following table shows the ports that DVR server uses for certain network service. Port # Variable Remote

264 Appendix D Mobile Viewer Comparison 3GViewer iPhoneViewer SmartViewer Handy Viewer Live 1CH Live Video 1CH Live Video 1CH Live Vid

LIMITED WARRANTY AVer Information Inc. warrants that this product to be free of defects resulting from faulty manufacturing or components under the

16 2.5.4 Install (2) NV8416T card and (2) I/O card (optional) 1. Remove the PC case cover. 2. Remove 2 brackets that cover the PC-Ex4I slot and 2

17 2.5.5 Connecting the Watchdog line The DVR program constantly monitors its operation. Connecting the NV6120T/NV6000T (6240T/6480T) /NV8

ii Important Notice  NV6480T Recording Specification When NV6480T card is connecting with 8 anlaog cameras on CH1~8 and 8 IP cameras on rest of ch

18 2.5.8 Connecting the Watchdog line to NV8416T 1. Look for the labeled RESET SW switch lead and connect it to the NV8416T card reset pin. 2. C

19 2.6 Connecting the Cameras, a TV and Audio device 2.6.1 Connecting the Cameras, a TV and Audio devices to NV6120T 1. Use the supplied AV connec

20 2.6.2 Connecting the Cameras, a TV and Audio devices to NV6000T 4. Use the supplied AV connection cable and connect it to the D-type AV IN port

21 2.6.3 Connecting the Cameras, a LCD Monitor, and Audio devices to NV8416T 1. Use the supplied AV connection cable and connect it to the DVI AV I

22 2.7 Dual Monitors Setup The NV DVR system Supports Single and Dual monitor displays. When using dual monitors, the Emap and Playback function wil

23 4. Select the Extended Desktop and then click Finish. 5. If user selected the Advanced mode, click the View button. 6. In Display Manager, rig

24 2.7.2 Graphic card with NVIDIA chipset 1. Click the NVIDIA nView, and select the Dualview mode. 2. Adjust each monitor resolution to 1024x768,

25 2.8 Sensor and Relay pinhole allocation on I/O Card 2.8.1 NV6120T/NV6240T/NV6480T/NV8416T The I/O Audio card enables you to connect (4) sensor i

26 2.9 The Sensor input and Relay output Specifications You may use the sensor input and relay output specifications table below for your reference.

27 2.10 Connecting POS (Point of Sales) AVer DVR can be integrated with POS system equipment. Connecting the POS equipment to AVer DVR system thru

iii FCC NOTICE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not

28 Chapter 3 Software Installation This chapter describes how to install the DVR software, drivers, install NV software license (NXU8000 series), an

29 3.1 Installing NV DVR Software and Drivers in Windows XP/7 Upon turning the computer on, the system automatically detects the newly installed ha

30 3.2 Installing NV Software License(NXU8000 series) DO NOT install Software License to multiple PCs, it won’t work if the license key has been fo

31 b. Click power button ( ) and click About button. The Product Information dialog is shown up and click License Upgrade button. 9. Next,

32 10. After getting the activation key (License.bin), click “Yes” and import your activation key (License.bin). 11. Then, DVR/NVR sys

33 3.2.2 For Upgrading Installation To upgrade the extra IP camera channels for existing NVR/DVR system, please follow the below steps to upgrade: 1

34 3. Next, DVR System would ask user to enter the activation key (License.bin). If user didn’t get the activation key (License.bin),then, click “

35 4. After getting the activation key (License.bin), click “Yes” and import your activation key (License.bin). 5. Then,

36 Chapter 4 Using the DVR Software 4.1 Running the DVR Software To run the application, double-click on your PC desktop. For security purpose,

37 4.3 System Setup Wizard The Setup Wizard can guide the user to complete the basic but important setting of DVR system. After login the DVR/NVR sy

iv Following information is only for EU-member states: The use of the symbol indicates that this product may not be treated as househol

38 4.3.1 System Setting Wizard In System Setting step, select the language of DVR system and interface, current time zone of DVR is located, setup n

39 4.3.2 Network Setting Wizard Setup the IP address of DVR and configure the DDNS. After completed all configuration, click Next to save the settin

40  dyndns.org - Domain Name: The user has applied on website www.dyndns.org. - ID: The account ID that user has created on website www.dyndns.or

41  Register the Domain Name on http://ddns.avers.com.tw 1. User Login: Browse the website ddns.avers.com.tw with Microsoft IE or Netscape Navigat

42 4.3.3 Display Setting Wizard Set monitor resolution and frequency. The DVR system support dual monitor and user need to set a primary monitor w

43 4.3.4 Storage Setting Wizard To create partition, format the hard disk and select storage path for saving recording data. Also, user can setup iS

44 2. Click on the hard disk is in Volume Information table and click Create volume to set the size of partition. 3. User can enter the partition si

45 4. Each partition is assigned a letter as a volume ID. When user select a storage path, please remember the volume ID match to which partition. To

46  Release the partition: User can delete the partition. When the partition has been deleted, all data save in partition will be erased 1. In Vol

47  Format the hard disk: To format a hard disk or a partition. All data on the hard disk or partition will be erased. 1. Select

v TABLE OF CONTENTS MANUAL UPDATES ...

48  iSCSI: To connect the iSCSI server that user has on LAN network. 1. Click iSCSI button. 2. Enter the IP address or DNS name of the iSCSI ser

49  Storage Path Set the directory on where to save the data. When there is not enough free space to record one hour data, the system automatically

50 2. In File Browser window, select the hard disk drive from Current Drive drop-down list. 3. Then, click New Folder icon to create a new folder f

51 6. After completing Storage setting, click Exit button and select Yes to save and exit the Setup Wizard. If user wants to modify some of setting,

52 4.4 Familiarizing the Buttons in Preview/Advanced Mode DVR system now supports 1024x768, 1440x900, 1680x1050, 1920x1200 or 1920x1080 display reso

53 Name Function (1) Exit Call up the Logout dialog box. In the logout dialog box, you may do the following: - Click Exit to close the DVR program.

54 Name Function (2) Split Screen Mode Select from 7 different split screen types to view all the camera, or one camera over the other or alongside o

55 Name Function (6) Setup Configure the system settings (see also Chapter 5). (7) PTZ Access PTZ control panel. Beside PTZ camera, DVR system also s

56 Name Function (13) iPOS Live To view the real time iPOS data of channels. Click the iPOSLive to call out the real time iPOS data window. User

57 Name Function (17) Full screen Use the entire area of the screen to only display the video. To return, press the right button of the mouse or ESC

vi 2.5.6 Connecting the Watchdog line to NV6120T ... 17 2.5.7 Connecting the Watchdog line to NV6000

58 Name Function (20) Volume Adjust the sound volume. (21) On Screen Keyboard If the keyboard is not available, you may use the Virtual Keyboard. (22

59 4.4.1 Using Event Log Viewer Show the record of activities that take place in the system. i - DVR system now supports HDD failure pre-detection

60 4. The events list which display on the screen can be saved as text file format. To save the events list, click Save button. 5. To view POS even

61 Using Counting Log Viewer 1. Select the Date and set a time period between After and Before for object counts searching. 2. Select the search E

62 Using the Object Log Viewer Click Object Viewer bar to view and search FaceFinder event log. (1)(2)(3)(4)(5)(6) Name Function (2) Search Mode Swit

63 4.5 Familiarizing the Buttons in Compact Mode To view in Compact mode, click Exit button. In the logout dialog box, click Compact. Name Funct

64 4.6 Familiarizing the Buttons in Playback Mode To switch in Playback mode, click Playback button at the lower right corner of Advanced/Preview

65 Name Function (1) Split Screen Mode Select from 6 different split screen type to playback the recorded video file of all the camera, or one camer

66 Name Function (4) Hour Buttons Select and click to playback the recorded video file on the specific time frame. i The Hour buttons r

67 Name Function (7) Status bar Display the recorded date, time and play speed. (8) Camera ID Show the number of cameras that are being viewed. When

vii 4.7 FAMILIARIZING THE BUTTONS IN PTZ CAMERA CONTROLLER ... 71 4.8 SETTING UP AND USING THE EMAP...

68 Name Function (10) Export Export includes Snapshot, Print, Output Video Clip, and Backup function. Snapshot: Capture and save the screen shot ei

69 Name Function (20) De-interlace To enhance the video quality. Set the de-interlace mode to #1, if you are capturing motionless picture and #2, if

70 4.6.1 Watermark Verification Now, DVR supports watermark-checking to identify the authenticity of playback video. DVR program can only verify one

71 4.7 Familiarizing the Buttons in PTZ Camera Controller (9) (8) (7) (6) (5)(2)(1)(3)(4)(10)(11) Name Function (1) Close Exit PTZ camera controll

72 4.8 Setting Up and Using the Emap Emap can hold up to 8 maps in *.bmp/*.jpg format. You may locate the camera, sensor and relay on the map. To Se

73 4.8.1 To Use the Emap 1. Click Emap. 2. In the Emap screen, click the camera icon to switch on the area where the camera is located on the map

74 4.9 To Cut and Save the Wanted Portion of the Recorded Video 1. Use the Playback Control buttons or drag the bar on the playback progress bar

75 4.10 To Bookmark a Section of the Video 1. Click Bookmark. The video playback stops when the bookmark button is executed. 2. In the Bookmark d

76 4.11 To Search Using the Visual Search 1. Click Visual Search. 2. In the Visual Search Setting dialog box, select the Camera number and the d

77 4.12 To Search Using the Event Search 1. Click on the video screen on where you want to search. 2. Click Event Search. The Event Search text (r

viii 5.7 SENSOR SETTING ... 156 5.8 RELAY SETTING ..

78 4.13 To Search Using the Intelligent Search 1. Click on the video screen on where you want to search. 2. Click Intelligent Search. The Intellig

79 4.14 To Setup the PTZ/IP PTZ Camera To enable the PTZ function of the camera and setup related setting of PTZ function. 1. In the PTZ control pa

80 camera. 10. OSD: To allow call out PTZ camera factory’s OSD setup menu if the PTZ camera has supported. The OSD setup menu may vary that depends

81 14. User also can click PTZ icon to call out on-screen PTZ control bar and use mouse to drag on screen to move the PTZ camera lens direction. 15

82 Chapter 5 Customizing the DVR System In the Preview/Advanced screen mode, click button to customize your DVR. When the DVR configuration set

83 certain days, enable the Delete event and alarm log after check box and enter the numbers of days in Days text box. To change logs save direction,

84 (6) TV Out Select the camera you want to appear on TV and set the time gap from 3 to 10 sec. before it switches to the next camera. i TV Out funct

85  Fixed Layout i The Advance tab will be available when the Display 21 card is installed. (1) Select the video source from drop down list. If use

86 - Default user Automatically log in to the selected default user when the DVR is executed. (10) Miscellaneous Enable the conditions in Miscellane

87 - Enable Overlay To enhance video signal for better video quality. i Enable Overlay doesn’t support on Windows 7. - Enable Liveplayback Mark to