AVer SF2111H-DR User Manual

AVer SF2111H-DR User Manual

7 3. Installation steps (1) Use screws to lock the bottom of camera to the ceiling or the wall. (2) Use 3-Axis to adjust the lens angle. (3) Close

8 Power Over Ethernet (PoE) Set up the IP camera through Power over Ethernet (PoE). PoE is a technology that integrates power into a standard LAN inf

9 IP Assignment There are two ways to find IP Camera: − Finding IP Camera by using “NXU Lite recording software” − Finding IP Camera by using “IP i

10 3. Click “Setup” button. 4. Click “Add IPCam” button. 5. Select “IP Camera” item.

11 6. Key in IP Camera’s ID and Password (default is admin/admin) and click “Auto Search” to find camera. 7. In Search Result window, click it th

12 Finding IP Camera by using “IP installer” 1. Use the software, “IP Installer” to assign the IP address of the IP camera. The software is in the a

13 IP Installer configuration: 6. IP Installer will search all IP cameras connected on the LAN. The user can click “Search Device” to search again.

14 Using DHCP Server/Router Network To use DHCP, please check DHCP and click “Submit” then click “OK”. It will apply the change and reboot the Device

15 Using NON-DHCP Server/Router Network In Non-DHCP server/router network, the static IP address must be assigned to the device each time when addin

16 IP camera IP addresses: 8. A quick way to access remote monitoring is to left-click the mouse twice on a selected IP camera in “Device lists” in

Table of Contents PREFACE ...

17 9. Then, please key in the default “User name” and “Password”, both of which are “admin”.

18 Install ActiveX Control The first time you attempt to view the camera video via Internet Explorer, it will ask you to install the ActiveX componen

19 5 When the following dialogue box appears, click “Yes”.

20 Using the IP Camera Browser Interface The admin have the full access to the IP camera browser interface. The menu on the left, you can expand and

21 Name Function (3) Bandwidth Show current IP camera’s transmitting bandwidth (4) FW Version Show IP camera’s current firmware version (5) Lo

22 System > General In this section, only admin level is authorized to configure the IP camera system maintenance and the date and time settings.

23 Name Function (4) Firmware Upgrade Upgrade the firmware to the latest version. To Upgrade the IP Camera Firmware 1. Download the file from ou

24 System > General > Date & Time In the “Date & Time” tab, the administrator can set and update the system’s date and time. After fil

25 Name Function (4) Setting Method Select the date & time settings method. Sync with current PC – Obtain the date and time setting on the curr

26 password in “Confirm”. Then, click “Add/Set”.  User List: Click edit to change the account password. To delete the user account, click Remove

SYSTEM > ADVANCE > HTTPS ... 38 SYSTEM > ADVANCE >

27 System > Network Setting > Setting  Device Name: Used to name the IP camera to search more easily for this specific one among all connecte

28 System > Network Setting > Sever Used to send out the video via Email or FTP, or to save on NAS.  Mail Setting: Used to send out the video

29  NAS Settings: Used to send out the video to NAS server. a. Enter necessary information in “Location”, “Workgroup”, “Account Name” and “Password

30  Status - Common warning message: Updating! Failed(1), Please check your DNS setting. Failed(2), Please check your internet connection. Failed(

31 System > Network Setting > Other 1 User may need to assign different port to avoid conflict when setting up IP assignment. Click Apply to s

32  RTP Start and End Port: in RTSP mode, you may use TCP and UDP for connecting. TCP connection uses RTSP Port (554). UDP connection uses RTP Star

33 System > Network Setting > Other 2 Multicast Setting (based on the RTSP Server): User can setup two streaming based on the RTSP Server. Mul

34 Step 2: Step 3: Select Media/open network stream 3. Select force multicast RTP via TRSP 2. Select Demuxers and RTP/RTSP 1. Select all

35 Step 4: Input rtsp://[IPCAM Address] / [RTSP Path] The URL address should be the same as the RTSP path in Video Stream (System-->Video Stream)

36 [Notice] a. If the received image is not from the required IP camera, please adjust the value. (Change either IP Address or Port number) b. If

1 Preface The SF2111H-DR is a H.264 2-megapixel, full HD dome camera with 3-axis adjustment and a vari-focal lens that allows you to li

37  Bonjour: This function enables MAC systems to link to this IP Camera. Please key in the name here (Safari supports Bonjour protocol).  LLTD: I

38 System > Advance > HTTPS HTTPS (Hypertext Transfer Protocol Secure): Https can help protect streaming data transmission over the inter

39 Created Request: Setting the secure identification and apply it. There are two ways to set Certificate- Install Signed Certificate or Create Self

40 System > Advance > SNMP SNMP (Simple Network Management Protocol) provides a simple framework for administering networked hardware.

41  SNMPv3: For data security reason, the authentication and encryption assurances are added when developing SNMPv3. The user has to give not only t

42 System > Advance > Access list You can deny an IP address or a range of IP address so that they cannot access the IP camera. Tick the "

43 System > Advance > QoS/DSCP QoS/DSCP(Quality of Server/Differentiated Services Code-point) specifies a simple mechanism for classifying and

44 System > Image Admin and operator levels can adjust the Image setting. There are 5 tabs: OSD, Preference, Exposure, Advanced, and Privacy Mas

45 System > Image > Preference In Preference tab, you can tune the IP camera white balance, change the video orientation, and adjust the brigh

46 System > Image > Advanced Click Default button will back to factory default setting.  Sense-UP: The main purpose of sense-up is to provide

2 Hardware LED Built-in 18 IR LED IR Distance-15M I/O 1 Sensor in / 1 Relay Out Video Out 1 Audio In 1 G.711 (64K) and G.726 (32K,24K) aud

47 System > Image > Privacy Mask For the security purpose, there are three areas can be setup for privacy mask. Click Area #(Area 1, Area 2, Ar

48 System > Video Stream> General  Input Resolution: Select the video resolution that is the maximum resolution supported in Stream 1 and Stre

49 System > Video Stream > Stream1  Basic Mode Click Apply to save the configuration. − Resolution: There are 8 resolutions can be chosen – 19

50  VBR: 1(Low) ~10(High) – Compression rate, the higher the compression rate, the better the picture quality is; vise versa. The balance between V

51 System > Video Stream > Stream2  Basic Mode Click Apply to save the configuration. − Resolution: There are 8 resolutions can select -- 192

52  Advanced Mode Click Apply to save the configuration. − Resolution: There are 8 resolutions can select -- 1920x1080, 280x720, 640x480, 320x240,

53 System > Video Stream > Stream3 3GPP Streaming is designed for mobile viewing.  Stream 3 Setting: Enable or Disable 3GPP Streaming.  3

54 System > Audio IP camera supports 2-way audio (mono). User can send audio from IP camera built-in MIC (depending on different models) to remote

55 System > SD Card Please Insert SD/SDHC card before use it. Make sure pushing SD/SDHC card into the slot completely. [Note]The use of the SD/SD

56 Event > Arrangement > Motion Motion Detection: IP camera allows 3 areas motion detection. When motion is triggered, it can send the video to

3 System Image Snapshot Yes Full Screen Monitoring Yes Privacy Mask Yes, 3 different areas Compression Format H.264/ JPEG/ MPEG-4 Video Bitrates

57 Event > Arrangement > Preference  Record File:  File Format: IP camera allows 3 different types of recording file to change its record s

58 Event > Schedule  Schedule: After complete the schedule setup, the camera data will be recorded according to the schedule setup.  Snapshot: A

59 Event > DI/DO IP camera supports 1 input/1 output (depending on different models). When input is triggered, it can send the video to some speci

60 Output Setting: Mode setting: OnOff Switch: Relay status is based on sensor triggered times. Time Switch: To restore the origin

61 Network Configuration  Configuration 1 a. Internet Access: ADSL or Cable Modem b. IP address: More than one real IP c. IP camera and PC con

62  Configuration 2 a. Internet Access：ADSL or Cable Modem b. IP address：one real IP c. IP camera and PC connect to the internet d. Device nee

63 Factory Default 1. To recover the default IP address and password, please follow the following steps. 2. Remove power, and press and hold the bu

64 Troubleshooting Here are some useful tips on how to solve some common problems. Problem Solution I forgot the account and password for SF2111

65 Appendix SF2111H-DR is compliant with SD/SDHC card and to ensure recording quality, and please use memory cards over 2G and Class 4 a

66 COPYRIGHT © 2012 AVer Information Inc. All rights reserved. All rights of this object belong to AVer Information Inc. Reproduced or transmitted in

4 Package contents Item Descriptions 1. SF2111H-DR 2. Accessory pack 3. RJ45 socket 4. Power Adaptor (DC 12V /1A) (Optional) 5. CD (User’s

67 Limited Warranty AVer Information, Inc. (“AVer”) warrants that the applicable product (“Product”) substantially conforms to AVer’s documentation f

68 Governing Law and Your Rights This warranty gives you specific legal rights; You may also have other rights granted under state law. These rights

5 Product Installation Monitor Setting 1. Right-click on the desktop. Select “ Properties” 2. Change “Color quality” to “Highest (32-bit)”.

6 Hardware Installation and I/O Pin Assignment 1. Connect a power adapter and IP camera to PC or local network. 2. 3-Axis Gimbals Adjustments Onc