AVer SF2012H User Manual Page 1

AVer SF2012H-D User Manual

6 Hardware Installation and I/O Pin Assignment 1. Connect a power adapter and IP camera to PC or local network. 2. 3-Axis Gimbals Adjustments Onc

7 3. I/O Control Instruction I/O terminal connector – used in application, for e.g., motion detection, event triggering, alarm notifications. It pro

8 RELAY INSTALLATION EXAMPLE 2 Trigger the “Normal ON” (Normal Close) indoor illumination off when event / motion occur:

9 Power Over Ethernet (PoE) Set up the IP camera through Power over Ethernet (PoE). PoE is a technology that integrates power into a standard LAN inf

10 IP Assignment There are two ways to find IP Camera: − Finding IP Camera by using “NXU Lite recording software” − Finding IP Camera by using “IP

11 3. Click “Setup” button. 4. Click “Add IPCam” button. 5. Select “IP Camera” item.

12 6. Key in IP Camera’s ID and Password (default is admin/admin) and click “Auto Search” to find camera. 7. In Search Result window, click it the

13 Finding IP Camera by using “IP installer” Use the software, “IP Installer” to assign the IP address of the IP camera. The software is in the attac

14 IP Installer configuration: IP Installer will search all IP cameras connected on the LAN. The user can click “Search Device” to search again. Cli

15 Using NON-DHCP Server/Router Network In Non-DHCP server/router network, the static IP address must be assigned to the device each time when addin

Table of Contents PREFACE ...

16 IP camera IP addresses: 1. A quick way to access remote monitoring is to left-click the mouse twice on a selected IP camera in “Device lists” in

17 2. Then, please key in the default “User name” and “Password”, both of which are “admin”.

18 Install ActiveX Control The first time you attempt to view the camera video via Internet Explorer, it will ask you to install the ActiveX componen

19 5 When the following dialogue box appears, click “Yes”.

20 Using the IP Camera Browser Interface The admin have the full access to the IP camera browser interface. The menu on the left, you can expand and

21 Name Function (2) Login IP Show PC’s IP address (3) Bandwidth Show current IP camera’s transmitting bandwidth (4) FW Version Show IP camera’s

1 System > General In this section, only admin level is authorized to configure the IP camera system maintenance and the date and time settings. S

2 Name Function (4) Firmware Upgrade Upgrade the firmware to the latest versio

3 System > General > Date & Time In the “Date & Time” tab, the ad

4 Name Function (4) Setting Method Select the date & time settings method.

SYSTEM > NETWORK SETTING>SEVER ... 6 SYSTEM > NETWORK SETTING

5 password in “Confirm”. Then, click “Add/Set”.  User List: Click edit to ch

6 System > Network Setting > Sever Used to send out the video via Email or

7  NAS Settings: Used to send out the video to NAS server. a. Enter necessary

8  Status - Common warning message: Updating! Failed(1), Please check your DN

9 System > Network Setting > Other 1 User may need to assign different po

10  Security: Yes is required account and password to connect with this IP came

11 System > Network Setting > Other 2 Multicast Setting (based on the RTSP

12 Step 2: Step 3: Select Media/open network stream 3. Select force mul

13 Step 4: Input rtsp://[IPCAM Address] / [RTSP Path] The URL address should be

14 [Notice] a. If the received image is not from the required IP camera, please

COPYRIGHT ... 38 NOTICE ...

15 System > Image Admin and operator levels can adjust the Image setting. T

16 System > Image > Preference In Preference tab, you can tune the IP cam

17 System > Image > Advanced Click Default button will back to factory def

18 System > Image > Privacy Mask For the security purpose, there are three

19 System > Video Stream > General  Input Resolution: Select the video re

20 System > Video Stream > Stream1  Basic Mode Click Apply to save the co

21 − Video Format: H.264 or JPEG − RTSP Path: It’s a URL address

22 System > Video Stream > Stream2  Basic Mode Click Apply to save the c

23  Advanced Mode Click Apply to save the configuration. − Resolution: There a

24 System > Video Stream > Stream3 [Note] 3GPP mode suggested setting: 176

1 Preface The SF2012H-D is a 2-megapixel dome camera with 3-axis adjustment and a vari-focal lens that allows you to line up the camera

25 System > Audio IP camera supports 2-way audio (mono). User can send audio

26 System > SD Card Please Insert SD/SDHC card before use it. Make sure push

27 Event > Arrangement > Motion Motion Detection: IP camera allows 3 areas

28 Event > Arrangement > Preference  Record File:  File Format: IP cam

29 Event > Schedule  Schedule: After complete the schedule setup, the camera

30 Event > DI/DO IP camera supports 1 input/1 output (depending on different

31 Output Setting: Mode setting: OnOff Switch: Relay status is based

32 Status Information Click Apply button to save the configuration.  Networkin

33 Network Configuration  Configuration 1 a. Internet Access: ADSL or Cable M

34  Configuration 2 a. Internet Access：ADSL or Cable Modem b. IP address：on

2 Hardware I/O 1 in/ 1 Relay Out Video Out 1 Audio In 1 Audio Out 1 Power over Ethernet Yes Power Consumption DC 12V 470mA 3-Axis Gimbal Adj

35 Factory Default 1. To recover the default IP address and password, please fo

36 Troubleshooting Here are some useful tips on how to solve some common probl

37 Appendix SF2012H-D is compliant with SD/SDHC card and to ensure recording qua

38 FCC NOTICE (Class B) This device complies with Part 15 of the FCC Rules. Oper

39 Limited Warranty AVer Information, Inc. (“AVer”) warrants that the applicable

40 Governing Law and Your Rights This warranty gives you specific legal rights;

3 System Triggered Action Mail, FTP, Save to SD/SDHC card, Relay, NAS Pre/ Post Alarm Yes (Configurable) Security Password Protection Firmware Up

4 Package contents Item Descriptions 1. SF2012H-D 2. Accessory pack 3. Ethernet cable 4. RJ45 socket 5. Power Adaptor(DC 12V /1A) (Opti

5 Product Installation Monitor Setting 1. Right-click on the desktop. Select “ Properties” 2. Change “Color quality” to “Highest (32-bit)”.